If you encounter difficulties when trying to initialize the SD card via the EZVIZ APP, below are some troubleshooting steps to resolve the issue for you:

1. Ensure both the firmware of your camera and EZVIZ APP are running on the latest version.

2. Ensure the SD card is class 10 or rated at UHS-1. The file format of the SD card should be FAT32 for capacities below 64GB and exFAT for capacities of 64GB and above. Click Here to view partial test results of SD card compatibility.

3. Power off your camera, remove and reinsert the SD card, power the camera on and then initialize the card again on the EZVIZ APP.

4. To further rule out the SD card issue, you may try to test with a different SD card or install the card in question on another EZVIZ device. 

5. Try to factory reset your camera by holding the Reset button. This will turn the device to the default factory settings and might help resolve minor issues.

1. Download the EZVIZ APP to your mobile phone from the App Store (for iOS), Google Play (for Android), or HUAWEI APP Gallery (for HUAWEI).

2. Register an EZVIZ account with your email or phone number and log in.

3. Reset your camera by pressing the reset button for about 10-15 seconds, for some cameras you will hear the voice of "Reset successfully". Then wait for about 1 minute or a few seconds, when you see the indicator light change into red-blue flashing alternately or blue light flashing fast (for some cameras, there is no light change for your reference, that's ok, you just wait for about 1 minute).

4. Connect your phone to 2.4G wifi only, then tap the "+" button on the home page to scan the QR code that is on the label of the device. You can find a label on the back or bottom of the device. (Please make sure your phone is connected to 2.4G wifi only and you give the camera permission to the EZVIZ app)

5. Then follow the instructions on the APP to connect the device to your wifi.

6. After adding the device to your account, you will be able to view your cameras.

If you see "Unable to join network EZVIZ_SN" (the SN of your EZVIZ camera) or if you cannot connect to the Device AP during network configuration, we suggest you reset your camera by pressing the reset button for 4-5 seconds and restart the setup procedure.

Before doing so, please make sure that

1. Make sure that you have turned off the cellular data on your phone.

2. Make sure your device is in configuration mode. You can easily tell if the camera is ready by checking if the indicator light flashes blue quickly.

3. When configuring the network, make sure that your EZVIZ device is close to your Wi-Fi router. We recommend that you keep the distance less than 1.5 meters.

If the problem persists, please try the following method:

1. If you are using iPhone 15 Pro or Pro Max, please try with a different phone model;

2. Please check if you can find a Wi-Fi starting with EZVIZ_XXXXXX (the SN of your EZVIZ camera) in the Wi-Fi list of your phone;

3. If yes, please check if you can connect it manually. The password for the device Wi-Fi should be "EZVIZ_verification code" (a 6-digit capital letter code that you can find on the device label);

4. After the connection, go back to the EZVIZ app to complete the network configuration.

If the APP prompts "Account username or password error" when you try to log into your account, below are some steps to resolve the issue for you:

Step 1. Please make sure your account information and region are correct.

Step 2. If correct, please ensure you input the correct account password and please be reminded that the password is case-sensitive.

Step 3. Alternatively, you may tap on “Forgot password" on the login page and follow the instructions on the APP to reset a new password and re-sign into your account.

If the issue persists after following the above steps and you need additional assistance, feel free to contact the support team by emailing support@ezviz.com

Please follow the steps below:

1. Log in to your EZVIZ account.

2. On the Home page, click the 3-dot icon next to the name of your camera to enter the Device Settings page.

3. Turn on the Alarm Notification button, then you will be able to receive the messages when motion detection is triggered. 

4. For some other models, you need to enter Notification on the Settings page, enable Receive Device Message and EZVIZ App Notification.  

1. If you registered an account via email, please check your junk mail. If you still do not receive the verification code, you may have an email filter/block that is restricting this email. Please check with your email provider.

2. If you registered an account using a mobile phone number, please confirm that your mobile phone can receive SMS short codes. You can also try clearing the cache on your phone, restarting your phone, or inserting the SIM card into another phone to see if you can receive it.

3. If the issue persists after following the above steps and you need additional assistance, please provide your camera's SN, your phone number/email address, your country, the time of your request and a short video of the issue to the support center at support@ezviz.com.

Step 1: On the Devices page, tap the "+" icon at the top right, then tap "Add Device"

Step 2: Tap the scan icon at the top right or select the device type to add the device

Step 3: On the "Scan QR Code" page, tap the edit icon at the top right, then enter the SN manually to add the device.

**Please make sure you have the correct device serial number and device verification code first!

Step 1: Log in to your EZVIZ account, tap the profile icon on the top left 

Step 2: Tap Family & Guests

Step 3: Tap Add Sharing  

Step 4: Input a valid EZVIZ account to which you would like to share, and ensure the region of the guest account is the same as the owner account, then tap Continue 

Step 5: Select the devices you would like to share and you can edit the permissions by tapping the device. After the guest account accepts the invitation, it means the devices are shared with success. 

For this situation, you need to reconfigure the camera by following the steps below:

1. Press and hold the RESET button on your camera for about 5-10 seconds to reset it. This will allow you to start the process of reconnecting the device to the Wi-Fi.

2. Make sure your EZVIZ device is in Wi-Fi configuration mode.

3. Open the EZVIZ mobile app on your smartphone.

4. From the Home page of the app, tap the 3-dot icon next to the name of your camera to enter the Device Settings page.

5. Tap the "Wi-Fi" or "Network Settings>Wi-Fi".

6. Follow the prompts and instructions in the EZVIZ mobile app to enter the new Wi-Fi password to connect your device to your Wi-Fi network again.

Please check the following settings below:

1) Check the frequency band on your router to ensure that it allows 2.4 GHz network mode transmission if your device supports 2.4 GHz only..

2) Ensure that your mobile phone is on the WiFi and ensure that the WiFi network is active and functional

3) Check the network condition:

    •Make sure your network has no firewall and no other limit.

    •Ensure the router can distribute IP address to your device or disable the static IP setting (DHCP is enabled by default on all EZVIZ devices).

4) Reset your camera; ensure that your device is in ready mode or Wi-Fi configuration mode > then use the EZVIZ mobile app for device Wi-Fi configuration.

Step 1: On the login page, input the correct account and tap Forgot password? button 

Step 2: Tap Send to continue 

Step 3: Input the code in the picture to verify your account and then a 4-digit code will be sent to your registered email address or phone number 

Step 4: Input the 4-digit code you receive 

Step 5: Create your new password and tap Save to complete the process